AX25RTD.CONF(5) Linux Programmer's Manual AX25RTD.CONF(5)
NAME
ax25rtd.conf - ax25 routing daemon configuration file
SYNOPSIS
/etc/ax25/ax25rtd.conf
DESCRIPTION
The file /etc/ax25/ax25rtd.conf is the configuration file for ax25rtd.
The parameters of the options shown here are the default values except
the ones marked with (example)
ax25-maxroutes 256
ip-maxroutes 256
The maximum size of the three lists / caches. On overflow,
ax25rtd will substitute the oldest entry with the new one.
[1k2]
This marks the beginning of per-port definitions. Note that you
have to use port names as defined in axports(5) here, anywhere
else you may use the port or the device name.
ax25-learn-routes no
Set this to "yes", ax25rtd will add the routing information for
every heard frame (with complete digipeater path) to the kernel
AX.25 routing table. Note that ax25rtd's internal cache will be
updated anyway, regardless of this option.
ax25-learn-only-mine no
If you set it to "yes", only frames that are sent to (1) the
interface callsign, (2) any of the listeners on this device, or
(3) the callsigns specified by ax25-more-mycalls will be used to
update the internal cache and (depending on ax25-learn-routes)
the kernel routing table.
ax25-add-path db0ach (example)
This is useful on DAMA digipeaters. In this case, the DAMA mas-
ter has to be used for _every_ AX.25 connection, thus ax25rtd
will add this digipeater(s) to every target we learn that has no
digipeater path (yet). "db0ach" is just an example here.
ax25-more-mycalls dl1bke dl1bke-8 (example)
You can specify more calls as calls here that belong to this
interface... "dl1bke" and "dl1bke-8" are examples.
ip-learn-routes no
If set to "yes", ax25rtd will modify the IP routing table if it
receives an IP frame (directed to us). This is dangerous!
It should not screw up your routing table, though. Ax25rtd rec-
ognizes the netmask of the device and will adjust the route only
if it fits the netmask and the old route points to one of the
devices ax25rtd knows about (hence an AX.25 device).
The problems begin if you have more than one port and a user is
able to hear your outgoing traffic on at least two of them. Due
to technical reasons ax25rtd adjusts the route _after_ the ker-
nel has sent the reply to the received TCP frame already. This
has technical reasons.
If the remote does the same both are switching between the two
ports.
Don't use this feature unless you know what you are doing.
It _should_ be safe do enable this on one-port machines,
although I strongly recommend to set a network route instead,
i.e.:
route add -net 44.0.0.0 scc3
Note that ax25rtd's internal cache will be updated anyway,
regardless of this option.
irtt <irtt>
If ip-learn-routes is enabled this will assign newly added
routes an initial round trip time (IRTT) for TCP. <irtt> is mea-
sured in msec, hence
irtt 10000
sets the irtt to 10 seconds. A value of 0 disables this feature
(default).
ip-adjust-mode no
If you set this option to "yes" ax25rtd will change the IP
encapsulation mode according to the last received IP frame.
The problem with this option is that the kernel AX.25 sends a
received IP frame to the IP layer regardless if it was sent in
UI frame encapsulation "mode datagram (dg)" or in I frame
encaps, hence in an AX.25 connection, "mode virtual connect
(vc)". The Linux kernel will respond to this frame before
ax25rtd can adjust the mode. If the remote does the same... You
get the picture.
Don't use this feature unless you know what you are doing.
arp-add no
This option, if set to "yes", changes the ARP table to the
source callsign of the received frame. It should be harmless,
just has the the effect that if it is a new entry, the Linux ARP
code will send one ARP request before ax25rtd has adjust the ARP
table. If there was already an existing ARP entry for this IP
route, one IP datagram will be sent to the old address. Not
really a problem, I hope.
SEE ALSO
ax25rtd(8), ax25rtctl(8).
AUTHORS
Jrg Reuter <jreuter@poboxes.com>
Llaus Kudielka OE1KIB
Linux 11 November 2003 AX25RTD.CONF(5)
